How to Make a Rangefinder? – Complete Guide with Pro Advice, Tips, FAQs, & More

If you are wondering how to make a rangefinder then we are here to help!

Let’s go!

Making Rangefinder Using a Laser and a Camera

Kevin Le Brun built a rangefinder using a laser (a beam of light) and a camera. He used a laser pointer and a digital camera to make a rangefinder. A rangefinder is a device that measures distance by sending a beam of light across a target and measuring how long it takes to return. This is done because lasers are very accurate. You can use this method to measure the distance between two points or even three-dimensional objects.

Note: If you want to know a complete guide and tutorials about rangefinder click HERE.

Detecting the Laser Using Open CV

Install OpenCV on Raspberry Pi using pre-built binaries or compiling from source code.

A simple program that uses the Raspberry Pi camera module

to detect when a laser beam hits the screen. This program also tracks the location of the laser beam using the Python library pygame.

To ensure everything works correctly, I check my captured images to make sure the laser is correctly tracked. If you’re using a green laser, or if your laser isn’t correctly tracked, you’ll need to adjust the hue saturation and value thresholds of the program accordingly.

You can also increase the resolution by rotating the camera by 90 degrees using the full-width function. This increases the resolution to the maximum possible value supported by the camera. The distance will be much more accurate.

As follow-ups, I’ll need to work on the accuracy improvements I mentioned above and make an enclosure for the rangefinders. The enclosure will need precision to ease wall-to-wall measurement.

Note: If you want to know Binoculars vs Rangefinder Which to Buy the First click HERE.

How to Make a Rangefinder?

How to Make a Rangefinder?

Making a Cheap Laser Rangefinder for Arduino

Laser tape measures are very useful tools for measuring distances. They are also used as a kind of laser rangefinder. This is an example of how you could use a laser tape measure as a distance sensor.

Hardware components

A simple Arduino project using an LCD display, a laser pointer, and a tape measure. This project uses an LCD display, a tape measure, and a laser pointer.

Note: If you want to know Which Courses Are on the Bushnell Neo Xs Golf Gps Rangefinder Watch click HERE.

Hand tools and fabrication machines

Laser tape measures are used to measure distances. They are cheap and easy to use. There are many different types of laser tape measures available. You can buy them online or in stores. Most of them cost about $20. Some models have a larger range, while some others have smaller ranges. In order to make laser tape measures work properly, we need to calibrate them. This means that we need to set the distance between the device and the object that we want to measure.

We also need to know how far away the object is. Once we do this, we can calculate the distance between the device’s sensor and the object.

To do this, we need to send commands to the device. For example, if the object is 10 meters away, then we should send a command to the device to tell it to start measuring. Then we wait until the device sends back the measurement. Once we receive the measurement, we can calculate the actual distance between the device and our object.

Laser rangefinders are expensive devices, and you need a lot of them if you want to cover large distances. You could make your own laser rangefinder using an Arduino board and a laser diode, but this solution is much more complicated than the original laser tape measure. A better solution is to use a microcontroller such as the STM32F103C8T6. This chip allows you to control a laser diode, and you can also get data from sensors such as accelerometers, gyroscopes, or magnetometers.

Laser tape measures with a high degree of accuracy, but you’ll lose your original firmware.

A laser tape measure is a kind of measuring device. You can use it to measure distance or size. Laser tape measure uses a laser beam to do this job. There are many kinds of the laser tape measures. X-40 is not the only name of them. We should check out other types of laser tape measure first.

Note: If you want to gain information about Sig Rangefinder Binoculars Why Discounted clicks HERE.

Conclusion

We hope that now you know how to make a rangefinder.

If you still have some confusion, do let us know in the comments below.

If you want to know more information about rangefinder click HERE.

Author

  • John Moses

    John is the Editor in Chief here at The Outdoor Stores. His area of expertise ensures that there is no one better to suggest which rifles are most suitable for your hunting experience. He is also available for you to contact him personally to discuss the types of animals you want to hunt and the terrain you will be hunting on. Feel free to read his posts for expert opinion on Rifles, Scopes, Rangefinders, Bonoculars and Monoculars.

You Might Be Interested In...

Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Might Be Interested In!