Table of Contents
How to scope a mount is a question asked by many…
How to mount a scope on a Remington 700 is a question we are going to cover today so…
Let’s get started!
How To Mount A Scope On A Remington 700?
The Remington 700 has been around since 1957. It was designed by John Moses Browning. It is known as the best hunting rifle ever made. It is also used for target shooting. The best thing about this gun is its accuracy.
Accuracy at long range requires more than a good rifle. You also need a perfect scope alignment. Mounting a scope on a Remmington 700 requires knowing how to do it.
Note: If you want to know a complete guide and tutorials about scopes click HERE.
Why Should You Care About Scope Mounting?
A scope is a device used to magnify images. This allows you to see things more clearly. You use a scope when you want to be accurate when shooting.
Mounting scopes correctly is very important. You should use high-quality tools when mounting your scope. Alignment is also crucial. Make sure you get it right before you aim.
Tools You’ll Need To Mount A Scope On A Remington
Mounting a sight of any type to your rifle requires precision and attention to detail. You’ll need a few tools to do this correctly. Your scope should be the right size for your gun. Your scope base should fit your scope perfectly. A tightener should hold your scope firmly in place. A barrel leveler should make sure your barrel is straight.
How To Mount A Scope On A Remington?
Mounting a scope on a rifle is certainly comparable to art with a high-level perfection. One little misalignment may get you disappointing results. Especially when it’s a long-range rifle like the Remington 7mm SA. So, here is the essential tips and how-to mount a scope on a Remington 700.
1. Choosing the Right Scope and Base
You need to get the right scope base after getting your gun. A two-piece Picatinny scope rail is better than a one-piece. The Remington 700 has an exit port with recoil, so you should get a two-piece Picatinny rail instead of a one-piece.
A 60-minute scope with a standard 20-minute base gives you an MOA of 80 minutes. Adding another 20 minutes onto the rings gives you a total of 100 minutes of MOA. You should always be aware of your scope’s range when using it.
Note: If you want to gain information on How to Dial in a Scope click HERE.
2. Use Leveling Kits and a Base
Mounting rifle scope to a Remmington 700 starts with a mounting block. It holds the rifle tight and firm and levels it with fine height adjustments. First, place the rifle on the base and put a bubble level onto the barrel. Then level the gun by placing a bubble level on the handle. Finally, mount the rifle scope to the rifle.
3. Aligning the Scope Right
To align the scope to the muzzle, you need to take both the vertical (up/down) and horizontal (left/right) positions into account. Some scopes come 90°-angled, so you want to have your vertical scope turret on the top of the scope. You may also want to adjust windage by turning the windage knob on the side of the scope. Most manufacturers place their logo as their reference mark on the opposite side of the ejection port, so you’ll want to turn that around to match the direction of the logo.
4. Tighten the Rings Properly
A lapping bar should be used to adjust the alignment of the scope rings. This is done to ensure that there is no misalignment when using the scope.
5. Keep It in Your Natural Position
The scope should be comfortable to use. It should fit your face well. Eye relief should be adjusted properly. The marking eye relief stage of scope is important because you may need to adjust it later.
Note: If you want to gain information about Who Makes Redfield Scopes? click HERE.
6. Go up With Bigger Scopes
A higher base helps you have better clearance underneath, but it makes the scope harder to hold steady. You should consider a low-base scope when shooting a big game.
7. Get the Max Eye Relief
You should use a ring with the lowest possible height so that you don’t have to strain your eyes by lifting your head. However, if you’re using a larger scope with a bigger objective than the ring, then follow the first step mentioned above.
8. Mounting Scope on the Rifle
A scope should be mounted on a Remington 700 using two bubble levels. The first level should be placed on the base and the second on the barrel. These levels must be centered when tightening the rings.
9. Zero the Scope on the Remington
You should always zero your scope before shooting. A rangefinder helps you do this. When you’re ready, aim at your target and shoot. Adjust the elevation or windage until you hit your target.
Be sure to keep track of the distance you’re shooting at, and adjust accordingly. You should also be using the correct settings for your rifle. Don’t forget to take into account your eye relief when adjusting your sights.
Note: If you want to know How to Paint a Rifle Scope click HERE.
How to Mount a Scope on a Remington 700?
Safety Tips When Mounting A Scope On Remington
Safety rules when mounting a scope to a rifle.
1. Empty the Chamber First
Before you start using your rifle, make sure it’s unloaded. Never load a gun when it’s still holding ammunition. Slide the magazine first, or unload the chamber before you begin working on a Remington Model 700.
2. Be Careful With the Base
Scope rails are important things to consider when building your Remington rifle. You should use a 2-piece Picatinny scope base instead of an EGW Weaver base. This will help prevent ejecting cartridges from hitting the base of the gun.
3. Test Before Shooting for Real
Don’t trust your scope, even if you’ve tested it before. You should always check out the scope in the field before going for a hunt. Practice shooting without using the scope first.
If you want to know more information about scopes click Here.
Conclusion
We hope that now you have a better insight into how to mount a scope on your Remington 700!
